Tazer JL Mini Programmer for 2018+ Wrangler JL Gladiator JT

Tazer JL Mini from Z Automotive is an essential tool for Jeep owners of the 2018+ Wrangler JL and Jeep Gladiator JT. The Tazer JL Mini works on all models, including international models!

Simple, plug-in installation – just unplug the SGW module and plug the Tazer JL Mini in its place. Located above the OBD2 Diagnostic connector. To make it easier for removal and reinstallation for dealer visits, add on the SGW Extension Cable.

Features are all accessed using the dash display, using steering wheel buttons to navigate the menus. Tazer JL Mini features can be broken into two categories. Vehicle Settings – which are changes made to the Jeep like tire size, gear ratios or other settings to accommodate upgrades or modifications. These changes will continue to operate after the Tazer JL Mini is unplugged. Live Functions – which are functions the Tazer JL Mini performs live, only while plugged in.

• Change Tire Size
• Change Gear Ratio
• Change Transfer case LOW ratio
• Enable/Disable TPMS system
• Change TPMS pressure warning limit front/rear (25psi - 85psi)
• Enable/Disable Backup camera
• Enable/Disable Cargo Camera input (8.4 Uconnect only)*
• Enable/Disable CD (wired audio) input*
• Enable/Disable TravelLink/XM traffic&weather
• Change Daytime Running Lights (DRL) region (type)
• Change DRL location
• Enable/Disable DRL Dropout function
• Enable/Disable factory fog lights
• Enable/Disable Fog Light Dropout (when Fogs shut off while High Beams are on)
• Enable/Disable Factory Halo lights (including BCM output for adding Halo’s)
• Enable/Disable Onetouch lane change
• Change Headlight type (std/LED)
• Change Fog light type (std/LED)
• Change Taillight type (std/LED)
• Change Front Turn Signal type (std/LED) supports aftermarket LED lights too
• Enable/Disable Trailer Tow setting
• Enable/Disable Aux Button settings
• Enable/Disable Blind Spot detection (if hardware added or removed)
• Enable/Disable/Change Parksense configuration
• Disable Electronic Sway Bar (if removed from vehicle)
• Disable Front Axle Disconnect module for axle swaps
• Disable Front and Rear Lockers for axle swaps
• Disable Electronic Steering Pump for hydraulic steering conversions
• Change cluster splash screen Wrangler/Sahara/Rubicon
• Change HVAC controls setting to allow use of dual zone controls on single zone Jeep (for those upgrading the 5″ radio)
• Enables use of Factory Anti-Locking Brake System to lock the rear inner wheel while making tight turns on the trail

• AutoStopStart disable : remembers last state of the auto stop start system and will set it for you the next time you start the vehicle
• AutoTracKill : remembers last state of traction control system and will set it for you the next time you start the vehicle
• Can disconnect sway bar in 2WD up to 30mph (any speed if button mapped SwayKill is used)
• Can use backup camera and added cargo/front/undercarriage camera or media player at any speed
• TurnCAM : automatic backup camera when turn signals are used (8.4 uconnect only)
• Dark Mode : Turns off all exterior lighting and dash/radio/shifter lights while parked with engine running.
• 3rd Brake Flash : Set rate and number of flashes to pulse the 3rd brake light when brakes are applied for increased visibility
• Light Show mode : 6 preset and 3 make-your-own Light shows that flashes all the exterior lights, perfect for car shows/first responders/off-road visibility. Control from Key Fob or steering wheel buttons. Can be enabled for in-motion use for parades, off-road and legal police/EMS.
• Axle Locker control (Rubicon) : Engage lockers in 2WD and 4Hi on demand.
• TC Kill : Turns off traction control, stability control and ABS.
• Hood Alarm : When the vehicle theft alarm is armed, monitors hood activity and will sound the alarm and flash light shows if opened.
• Cooldown mode : Turn engine fans on demand when the ignition is on, engine not running
• Line Lock : Can lock front brakes for an easy burnout
• Rock Crawl : Can lock all four brakes by pressing steering wheel buttons to hold the vehicle still, especially helpful when off-road.
• Winch Mode : Raise idle to 2000 RPM with a simple button press.
• Button Mapping : Use cruise up, down and right buttons as quick-access to some of Tazer JL’s functions, when cruise control is off.
• Display DTC’s : Shows the diagnostic codes that’s making the check engine light come on.
• Clear CELs : Reset that pesky check engine light. Good when you have mods that set the light and you know exactly why.
• 0 to 30 and 0 to 60 Timers : Displays 0-30 or 0-60 times on EVIC display
• Automatically blanks license plate lights when in Reverse on Gladiators, to remove glare on the backup camera at night.
• Vacuum/Boost gauge : Watch real-time Manifold Pressure, great for boosted/turbo applications
• Firmware updates : The new firmware is available periodically, always free!